Post by Mason on Aug 10, 2008 9:24:05 GMT -6
Barrel Threads
Freak Tip Threads - .866" 16tpi double threaded 180deg apart
Barrel Threads
Autococker: UNF 15/16-20
A5/ProCarabine: UNF 7/8-20
ATS (Barrel): UNF .835-20
ATS (Unisizer): .760-56
Impulse: UNF 15/16-12 DL (Dual Leads)
Phantom: Acme 0.860"-14
Angel: M24x2.0
Spyder: M22x1.5
Alien PB
Interceptor 05
Ram Screws 4-40x1/4
Under Trigger Guard: 8-32x3/8
Interceptor 06
Ram Screws 4-40x3/8
Under Trigger Guard: 8-32x3/8
Remains 06
Ram Screws Front: 6-32x1/4
Ram Screws Back: 6-32x3/16
Under Trigger Guard: 10-32x5/8
Angel
Angel:
Angel LED, LCD & IR3 detents ----- 1/8" BSP
angel feednecks ----- M21x0.75
ball detent threads ----- M10x1.00
Trigger screws ----- M4x10mm
Bottom body grub ----- M4x6mm
LPR and battery caps ----- M19x0.75 (roughly 0.748"-34 in English units)
Autococker
valve retaining nut----- 5/8"-18 5/16" long hollow lock screw
valve locking nut (located on underside of body) ----- 5/16"-24 1/4" long set screw
cocking rod hex knob ----- 5/16" OD 10-32 stainless threaded hex standoff, 3/4" long
All (or most) newer hammer kits ----- 1/4"-28 x 1/2" setscrew, with the first approx. 3/16" turned down to just narrower than the 'Cocker body slot. (Itself 3/16".)
IVG 3/4-16
Bolt o-rings ----- 0.1" thick, 0.5" ID, 0.7" OD
front block bolts ----- 3/8-24 threads on '99 and earlier
9/16-24 threads on 2000 and later
detent ----- 3/8 -24
velocity adjuster ----- 3/4-16
3-way ----- 15/32"-32
ram - 6-32
cocker barrels ----- 15/16"-20, Oversize GH-7
Autococker LPR ----- 1/8" NPT
Pump arm ----- 10-32
Phantom
Barrel threads ----14 TPI Acme threads with a major dia. of 0.860"
nylock in bolt ---- 10-32 , ~0.147" long
Front grip frame screw ----- 6-32
Rear grip frame screw ----- 8-32
Impulse
feed necks ----- 32tpi, around .807" major dia
valve lock screw ----- 7/16"-20
frame screws ----- 1/4"-20, 1" long
front cap -----1"-16
impulse VA bolt ----- 3/8"-27
Viking
End-caps ----- 3/4"-20
Feed-neck ----- 15/16"-20, Oversize GH-7
Barrel ----- 15/16"-20, Oversize GH-7
BKO
Ram screws: (2) 10-32 x 1/2" (Button Head)
ASA Block screw: (2) 10/32 x 3/4" (Socket Head Cap)
Valve Retaining Set Screw: 3/8-24 x 1/4" (socket set screw, fine thread)
Tray - Body Screws: (4) 6-32 x 7/8" (Socket Head Cap)
Grip Frame - Tray Screws: (2) 8-32 x 3/8" (Allen Head is 4-40)(Button head)
Grip - Grip Frame Screws: (4) 6/32 x 1/4" (Button Head)
Trigger Set Screws: (3) 8-32 x 1/4" (Set Screw)
Valve Set Screw: (1) 1/8NPT plug
New Style Ball Detents (O-ring) Screws: (1) 6/32 x 1/4" (Button Head)
Bottomline: (2) 10/32 various length
Other
normal gauge/macro ------ 1/8" 27 NPT
grip frame/bottom line screws ------ 10/32
asa ------ 1/2 NPS tap
Freak Tip Threads - .866" 16tpi double threaded 180deg apart
Barrel Threads
Autococker: UNF 15/16-20
A5/ProCarabine: UNF 7/8-20
ATS (Barrel): UNF .835-20
ATS (Unisizer): .760-56
Impulse: UNF 15/16-12 DL (Dual Leads)
Phantom: Acme 0.860"-14
Angel: M24x2.0
Spyder: M22x1.5
Alien PB
Interceptor 05
Ram Screws 4-40x1/4
Under Trigger Guard: 8-32x3/8
Interceptor 06
Ram Screws 4-40x3/8
Under Trigger Guard: 8-32x3/8
Remains 06
Ram Screws Front: 6-32x1/4
Ram Screws Back: 6-32x3/16
Under Trigger Guard: 10-32x5/8
Angel
Angel:
Angel LED, LCD & IR3 detents ----- 1/8" BSP
angel feednecks ----- M21x0.75
ball detent threads ----- M10x1.00
Trigger screws ----- M4x10mm
Bottom body grub ----- M4x6mm
LPR and battery caps ----- M19x0.75 (roughly 0.748"-34 in English units)
Autococker
valve retaining nut----- 5/8"-18 5/16" long hollow lock screw
valve locking nut (located on underside of body) ----- 5/16"-24 1/4" long set screw
cocking rod hex knob ----- 5/16" OD 10-32 stainless threaded hex standoff, 3/4" long
All (or most) newer hammer kits ----- 1/4"-28 x 1/2" setscrew, with the first approx. 3/16" turned down to just narrower than the 'Cocker body slot. (Itself 3/16".)
IVG 3/4-16
Bolt o-rings ----- 0.1" thick, 0.5" ID, 0.7" OD
front block bolts ----- 3/8-24 threads on '99 and earlier
9/16-24 threads on 2000 and later
detent ----- 3/8 -24
velocity adjuster ----- 3/4-16
3-way ----- 15/32"-32
ram - 6-32
cocker barrels ----- 15/16"-20, Oversize GH-7
Autococker LPR ----- 1/8" NPT
Pump arm ----- 10-32
Phantom
Barrel threads ----14 TPI Acme threads with a major dia. of 0.860"
nylock in bolt ---- 10-32 , ~0.147" long
Front grip frame screw ----- 6-32
Rear grip frame screw ----- 8-32
Impulse
feed necks ----- 32tpi, around .807" major dia
valve lock screw ----- 7/16"-20
frame screws ----- 1/4"-20, 1" long
front cap -----1"-16
impulse VA bolt ----- 3/8"-27
Viking
End-caps ----- 3/4"-20
Feed-neck ----- 15/16"-20, Oversize GH-7
Barrel ----- 15/16"-20, Oversize GH-7
BKO
Ram screws: (2) 10-32 x 1/2" (Button Head)
ASA Block screw: (2) 10/32 x 3/4" (Socket Head Cap)
Valve Retaining Set Screw: 3/8-24 x 1/4" (socket set screw, fine thread)
Tray - Body Screws: (4) 6-32 x 7/8" (Socket Head Cap)
Grip Frame - Tray Screws: (2) 8-32 x 3/8" (Allen Head is 4-40)(Button head)
Grip - Grip Frame Screws: (4) 6/32 x 1/4" (Button Head)
Trigger Set Screws: (3) 8-32 x 1/4" (Set Screw)
Valve Set Screw: (1) 1/8NPT plug
New Style Ball Detents (O-ring) Screws: (1) 6/32 x 1/4" (Button Head)
Bottomline: (2) 10/32 various length
Other
normal gauge/macro ------ 1/8" 27 NPT
grip frame/bottom line screws ------ 10/32
asa ------ 1/2 NPS tap